Modelo
(Fabricante: E NORM)
Holy V-Mix,Nautamix,Vrieco-,Nauta Mixer,Konus Misch N.M. Heilig B.V. V-Mix 25.000 PLR Nueva máquina El mezclador se adapta a sus productos (por ejemplo, tamaño del grano, peso a granel) y entorno (por ejemplo, zonificación ATEX). - Capacidad: 25.000 litros cuando se llena el agua - Volumen utilizable: aprox. 22.500 litros dependiendo de las características del producto - Contenedores, tapas, brazo giratorio, tornillo mezclador, carcasa de salida V2A - Travesía de acero normal, pero está cubierta al interior del contenedor con una chapa V2A. -Todos los lubricantes están aprobados y certificados por H1 & Halal
Cabeza de remache giratoria BODMER KÜSNACHT tipo FMK 3 Año de fabricación aprox. 1980 Diámetro del eje del remache: máx. 10 mm Diámetro de la herramienta: 12 mm Carrera del cabezal del remache: 40 mm Velocidad del husillo del remache: aprox. 1400 rpm. Potencia del motor: 0,37 kW Alimentación: 380 voltios, 50 Hz - Ajuste de la presión del remache mediante la presión hidráulica infinitamente variable - Tope micrométrico para la limitación de la carrera- Movimiento de elevación mediante aceite hidráulico (máx. 45 bar) - Superficie de la brida mecanizada 115 mm con tuerca de fijación a la carcasa Longitud total: aprox. 800 mm Peso: aprox. 40 kg buen estado El cabezal de remachado tiene un cabezal multihusillo para colocar 2 o 3 remaches al mismo tiempo. Sin embargo, esto se puede desmontar y volver a utilizar normalmente. Sin embargo, para un uso normal, falta el cabezal de b ...
Cabeza a tope de ranura para fresadora, cabeza de fresado, CCCP / URSS STANKO Tipo 1502 Nº: 200 Año de construcción 1974 Tamaño de carrera: máx. 60 mm Velocidad de carrera: aprox. 200 - 500 carreras/min. Portaherramientas: 12 x 17 mm con placa de sujeción Placa de brida de la máquina de espaciado de orificios: 245 x 185 mm Orificio de montaje: 17 mm Diámetro de centrado en la placa de brida de la máquina: 190 mm - Tamaño de carrera ajustable mediante ajuste excéntrico- El accionamiento es infinitamente variable como con el cabezal vertical normal de la caja de cambios de la máquina- Accionamiento a través del conductor, centrado en el diámetro de centrado- Escalado de grados en la placa de brida +/- 45- Esta cabeza a tope de ranura tiene brida en lugar de la cabeza de fresado vertical normal (montaje en lugar de la cabeza de fresado vertical, cabeza de fresado) Peso: 42 kg ...
Interruptor mecánico de una sola posición, 2 uds BALLUFF BSE0008 BSE 44.0-RK capacidad de conmutación ( CC ): 220 V CC 0,5 A, 24 V CC 4 A capacidad de conmutación ( CA ): 250 V CA 6 A, 40 - 60 Hz conexión: Terminales de tornillo, 4 polos sistema de contacto: Cambiador de circuito doble (uno normalmente abierto y otro NC, aislado galvánicamente) Material: Termoplástico (tapa, carcasa), Material de contacto: plata fina, chapado en oro ¡Nuevo! Dimensiones ( interruptor ): 60 x 29 x 13 mm Dimensiones (embalaje): 140 x 80 x 20 mm
Interruptor de posición, interruptor de posición de seguridad, con palanca de rodillos SIEMENS 3SE3 120-1J ( 3SE3120-1j ) uno normalmente abierto / uno NC máx. 500 V máx. 10 A usado, probado ! Dimensiones: 125 x 40 x 63 mm
pressure:315 t distance between columns:1750 mm stroke:700 mm distance table/ram, max. stroke up, adjustment up:1200 mm table surface area:1600 x 1500 mm pressure of drawing cushion in table:125 t stroke of drawing cushion in table:200 mm die cushion area:1200 x 1400 mm table height over floor:750 mm ram surface:1640 x 1500 mm power requirement:55,0 + 11,0 kW weight:29,5 t dimensions (WxDxH):3,2 x 4,5 x 5,8 m Height above floor:5,1 m German Safety: permitted for manual loading:CE-Norm - EN 692, BGR 500 drawing cushion in table:hydraulisch cutting impact absorption:hydraulic
Pressure:250 t throat:450 mm stroke:8 - 135 mm no. of strokes:50 /min distance table/ram, max. stroke up, adjustment up:635 mm table surface area:1250 x 850 mm hole in the table:355 mm table height over floor:950 mm passage to the back:660 mm ram surface:790 x 610 mm ram adjustment:120 mm power requirement:18,5 kW weight:14,0 t Dimensions (WxDxH):1,5 x 2,8 x 3,65 m German Safety: permitted for manual loading:CE-Norm - EN 692, BGR 500 clutch:pneumatisch overload protection in ram:mechanisch ram counterbalance:pneumatisch
automatic switch plate 1x saw unit with saw, head and saw valve 40/80 1x turning unit with turning valve 30/60 with flange 9x units 30/60 with valve normal and flanges 5x units 20/50 with valve normal and flanges 1x oil distributor WK9; 1x bar feeder 4 meters; 1x chip conveyor VR500; 1x hydraulic unit 1 Knoll oil filter Without collets and ejectors, without platform and without tool monitoring. supplied tooling may differ from the pictures. We can send you more pictures. The scope of delivery regarding the tooling equipment could be different like pictures. Please, contact us for getting more information and pictures on mail(at)tar-mc.com or www.tar-mc.com
pitch taper:50 Aufnahme Detailed price on request depense on version and nos. ca. 500 - 1500 EUR + VAT /piece Diverse toolholders matching SCHIESS-VTL´s with SK 50 taper and T-slot clamping design! Diverse fixed boring bars in different dia. and length. Diverse boring bar adapter plates to adapt different boring bars. Diverse normal toolholders for toolshank 40 mm in version left or right
Description: Fabrication number: 5010 With saw blade that can be tilted at an angle of up to 45° and adjusted in height Saw blade diameter: 250 mm Table dimensions: 630 x 500 mm Minimum distance from the center of the saw shaft to the top edge of the table: 48 mm Height adjustment of the saw shaft: 60 mm Max. Saw blade diameter: 250 mm Bore of the saw blade: 20 mm Normal speed of the saw shaft: 4500 rpm Max. Cutting height: approx. 75 mm Cutting width to the right of the saw blade normal: 450 mm Cutting width in front of the saw blade normal: 250 mm Sliding table: Size of the table top: 520 x 320 mm Approx. Onsite Dimension. (l x w x h): 1,400 x 1,200 x 1,400 mm, weight approx.: 250 kg
: neu : ca. 8 Wochen ab Auftragse : Spanien : 8940 € : 185.06 € : 40 mm : MK 4 : 300 mm : variabel 80 - 1.170 U/min U/min : 2.4 kW : M32 : 655 mm : 440 mm : 1960 mm : 295 kg : automatisch 0,10 - 0,20 ( mm/U : 125 mm : 150 - 950 mm : 1.31 mm : 400 x 420 mm : 190 mm ERLO (MADE IN SPAIN) FOR DEMANDING WORKSHOP USE column drilling machine with vario gear variable revs 2 aut. feeds left-right drilling table with t-slots depth adustable end tool ejector drill guard CE norms user manual in GERMAN OPTIONS: coolant equipment and machine base with T-slots € 880,-- lighting equipment € 250,-- Reverse for Tapping € 785,-- LIEFERZEIT MIT OPTIONEN CA. 6 WOCHEN. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: neu : 2024 : 3983 : prompt, Zwischenverkauf v : Spanien : 6740 € : 139.52 € : 1 : 1 : 32 mm : MK 3 : 250 mm : 65 - 125 - 185 - 365 - 54 U/min : M24 : 600 mm : 640 mm : 2020 mm : 260 kg : 100 mm : 85 - 635 mm : 1.170 mm : 300 x 270 mm : 600 x 380 mm : 120 mm ERLO (MADE IN SPAIN) FOR DEMANDING WORKSHOP USE geardrive machine manual feed left-right drilling table with t-slots depth adustable end tool ejector drill guard CE norms user manual in GERMAN (sample photo) OPTIONS: lighting equipment € 250,-- coolant equipment and machine base with T-slots € 880,-- reverse for tapping € 785,-- DELIVERY TIME WITH OPTIONS APPROX. 6 WEEKS. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: neu : ca. 8 Wochen ab Auftragse : Spanien : 10050 € : 206.03 € : 40 mm : MK 4 : 300 mm : 75 - 150 - 235 - 325 - 47 U/min : 1.3 kW : Stahl: M 30, Guss: M 32 : 600 mm : 640 mm : 2020 mm : 305 kg : 0,1 — 0,2 — 0,3 mm/U : 160 mm : 125 mm : 420 x 400 mm ERLO (MADE IN SPAIN) FOR DEMANDING WORKSHOP USE geardrive machine 2 aut. feeds left-right drilling drill guard CE norms user manual in GERMAN OPTIONEN: lighting equipment € 250-- coolant equipment and machine base with T-slots € 880,-- Reverse for Tapping € 785,-- The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: neu : ca. 8 Wochen ab Auftragse : Spanien : 6360 € : 131.65 € : 32 mm : MK 3 : 250 mm : 245 - 355 - 490 - 710 - 8 U/min : M24 : 655 mm : 400 mm : 1900 mm : 260 kg : 100 mm : 85 - 635 mm : 1.195 mm : 300 x 270 mm : 120 mm ERLO (MADE IN SPAIN) FOR DEMANDING WORKSHOP USE column drilling machine with vario gear variable revs manual feed left-right drilling table with t-slots depth adustable end tool ejector drill guard COOLANT EQUIPMENTAND MACHINE BASE WITH T-SLOTS CE norms user manual in GERMAN OPTIONS: lighting equipment € 250,-- Tapping device (IR/RS) € 785,-- The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: neu : ca. 8 Wochen ab Auftragse : Spanien : 7520 € : 155.66 € : 40 mm : MK 4 : 300 mm : variabel 80 - 1.170 U/min : M32 : 655 mm : 400 mm : 1960 mm : 295 kg : 125 mm : 150 - 950 mm : 1.310 mm : 400 x 420 mm : 150 mm ERLO (MADE IN SPAIN) FOR DEMANDING WORKSHOP USE column drilling machine with vario gear variable revs manual feed left-right drilling table with t-slots depth adustable end tool ejector drill guard COOLANT EQUIPMENTAND MACHINE BASE WITH T-SLOTS CE norms user manual in GERMAN OPTIONS: lighting equipment € 250,-- Reverse for Tapping € 785,-- The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: neu : 2024 : 3982 : prompt, Zwischenverkauf v : Spanien : 10830 € : 222.02 € : 1 : 35 mm : MK 4 : 300 mm : stufenlos 100 - 2.000 U/min : 3 kW : bis M 27 : 1100 mm : 600 mm : 1950 mm : 360 kg : 0,10 / 0,20 / 0,30 (3) mm/U : 150 mm : 125 mm : 90-890 mm : 1250 mm : 480 x 480 mm ERLO (MADE IN SPAIN) FOR DEMANDING WORKSHOP USE column drilling machine with vario gear 1-stage V-belt drive with stepless variable speed with a frequency converter and digital speed display 3 automatic feeds chuck guard left-right drilling T-Slots and integrated coolant equipment in base stand integrated lighting drill guard HEIGHT ADJUSTABLE, ROTATING AND TILTING TABLE WITH T-SLOTS reverse for tapping fast and precise setting and control of the speed without switching operations and without defined levels more particularly robust parts for wear resistant operation and smooth running compact design with high p ...
: neu : 2024 : 3984 : prompt, Zwischenverkauf v : Spanien : 9250 € : 191.48 € : 1 : 32 mm : MK 3 : 250 mm : 65 - 125 - 185 - 365 - 54 U/min : M24 : 665 mm : 640 mm : 2100 mm : 260 kg : Automatisch 0,10 - 0,20 - mm/U : 100 mm : 85 - 635 mm : 1.170 mm : 300 x 270 mm : 665 x 400 mm : 120 mm ERLO (MADE IN SPAIN) FOR DEMANDING WORKSHOP USE geardrive machine 3 aut. feeds left-right drilling table with t-slots depth adustable end tool ejector drill guard CE norms user manual in GERMAN (symbol photo) OPTIONS: lighting equipment inkl. coolant equipment and machine base with T-slots inkl. reverse for tapping € 785,-- The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
sheet width: 3100 mm plate thickness: 40 mm pre-bending: 32 diameter of upper rolls: 460 mm diameter of lower rolls: 420 mm side roll diameter: 360 mm power capacity: 30 kW min. bending diameter: 1380 mm weight of the machine ca.: 30,1 t dimensions of the machine ca.: 6,3 x 2,3 x 2,6 m 4 Rolls Hydraulic Bending Machine Standard Features: - hardened and polished rolls - complete body made of ST-52 steel - hydraulically opened/closed drop end controlled from control panel - digital readout for side rolls - top and bottom rolls are driven by hydraulic and gearbox. Bottom rolls vertical movements are hydraulic powered - separate control panel - oil cooler - conic bending - in accordance to CE-norm Optional Accessories: - variable speed of rotation (5.325 Euro) - material feeding table (3.896 Euro) - center support (12.058 Euro) - 2 x side supports (11.258 Euro) The data for this ad was cre ...
band speed: 33 m/s grinding band dimension: 75 x 2000 mm total power requirement: 3 kW weight of the machine ca.: 75 kg turning speeds: 2800 U/min Standard equipment: - Knife set for flat steel - Complete knife set for angle steel shears - Complete normal punching equipment - Quick release device for punches up to 31 mm - Support table for punching device, rectangular notching and flat steel shears - Bending stamp with matrices V 40 and V 70 - Electric contact stop (1.000 mm) The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
flat steel: 350 x 10 mm round bar steel: 35 mm square edge steel: 30 mm L-beam: 80x80x8 mm hole diameter in sheet thickness: Ø 27 in 13 bzw. Ø 20 in 8 mm : 500 kN throat: 177 mm : 34 (Hub 15mm) blade length: 356 mm engine output: 3.0 kW weight: 950 kg dimensions: 1300x1100x1850 mm Standard equipment: - Knife set for flat steel - Complete knife set for angle steel shears - Complete normal punching equipment - Quick release device for punches up to 31 mm - Support table for punching device, rectangular notching and flat steel shears - Bending stamp with matrices V 40 and V 70 - Electric contact stop (1.000 mm) The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
HOT PRESS MODEL PL 90s 3000x1300 mm PS VBO TECHNICAL CHARACTERISTICS Platens dimensions 3000x1300 mm Stroke 400 mm Type of stroke Upstroke design (from bottom to top) Type of platen Assembled platens with coil and aluminum covering Total thrust 90 ton on 80% of the surface Pressing Cylinders N° 6 cylinders ø70 mm Specific Pressure 2.05 kg/cm2 on 100% of the surface 2.56 kg/cm2 on 80% of the surface Loading and Unloading Side3000 mm side Type of Heating system Oil boiler ? maximum temperature = 120°C Heating system specificationsElectric boiler 18 kW Opening Automatic by timer Control Board Standard Power supply 400V, 50Hz, 3ph Security device Safety rope around the press Red emergency Button Two Hand control Norma ...
ASC120, FEATURE VALUE, ENGINE 2x55 kW, FEEDING OPENING 2200x1400 mm, LENGTH 3,600mm, WIDTH 2,000mm, HEIGHT 3,100mm, WEIGHT 7,500kg, Inside the MIZAR ASC Series - Double Shaft SHREDDER, Uddeholm knives are used. The pieces are cut and sieved with knives mounted on the rotor and walls. The pieces come out in the width of the knives with sieve. The rotors move independently and are driven by an electric motor with a reduction gear. In case of a jam, the shredder clears it by rotating the rotors in the opposite direction., Once the problem is resolved, the rotors will continue to rotate in the normal direction. If the blockage cannot be resolved, a beep will sound and the machine will stop.
The Pall CFS system is designed as a single unit and can be installed directly in front of the filling line without the need for a buffer system. It is a completely independent process unit consisting of the following components: filter vessel Piping and connections Membrane cleaning system (CIP) integrity check Switchboard The hygienic design, the simple integrity test and the full automation ensure the microbiological safety of the system and usually allow the operation of the filling staff. Cluster filtering groups filter elements into clusters. Each cluster has its own outlet valve. During filtration, all clusters are open. Cleaning, sterilization and integrity testing are performed per cluster. Advantages of the CFS principle; Longer life Integrity testing on site Integrity diagnostics per cluster Special rinsing High specific flow rate Short flush times Constant flow in all candles ...
The Pall CFS system is designed as a single unit and can be installed directly in front of the filling line without the need for a buffer system. It is a completely independent process unit consisting of the following components: filter vessel Piping and connections Membrane cleaning system (CIP) integrity check Switchboard The hygienic design, the simple integrity test and the full automation ensure the microbiological safety of the system and usually allow the operation of the filling staff. Cluster filtering groups filter elements into clusters. Each cluster has its own outlet valve. During filtration, all clusters are open. Cleaning, sterilization and integrity testing are performed per cluster. Advantages of the CFS principle; Longer life Integrity testing on site Integrity diagnostics per cluster Special rinsing High specific flow rate Short flush times Constant flow in all candles ...
AFF International RED Filtration RotoCloneTM W Model N pipeline stainless steel 304L used Wet Dust Collector It is a humid filter for food industries The main flow is 20000Nm3/Hr The system is complete with 75 KW inverter for the main fan and control enclosure and inlet and outlet piping The RotoCloneTM Advantage The RotoCloneTM W is the most cost-effective, high-efficiency wet dust collector in its class. It combines a dust collector with a centrifugal fan, saving space and making it suitable for a wide variety of different applications. The distinguishing feature of the RotoCloneTM W is the addition of a fine water film on the impeller blades to capture even the smallest of dust particles. It is a cost-effective dust and grease collection solution that requires no compressed air or replacement cartridges or fabric bags. It is capable of handling hot, moist gas streams ...
Mitutoyo QUICK VISION ACTIVE 202 Optical measuring machine (Vision Measuring Machine) from the manufacturer Mitutoyo Specifications (See pictures) High efficiency No constant supervision is required. The operator can carry out other tasks. Minimisation of error sources Automatic edge detection The automatic edge detection function enables high reproducibility of measurements, regardless of the reproducibility of measurements. Image autofocus The image autofocus function enables reliable height measurements at high speed. Continuous measurement of multiple workpieces Grinding function With this function, a large number of workpieces positioned on the large number of workpieces positioned on the device are on the device in a single operation. Automatic measurement can be started after be started after rough positioning Pattern search The pattern search function automat ...
Centering ring diameter on the plate is 160 mm (not the standard 125 mm) This machine was regularly maintained and has CE norms. Type of used material: PBT GF 30 ABS/PA PP Service history: 3.2015 – Replacing the CF card reader with a floppy disk drive 5.2013 – Machine calibration 5.2009 – Machine calibration
Manufacturer: Trumpf Model: Trumatic L 6030 Year of manufacture: 2004 Power: 4 kW Laser: TLF 4000t Table: 6000 x 2000 mm with Rotolab CE Norms
One(1) aluminium roll forming production line for the production of spacer bars for double glazing. - Dimension of machines: 18-20m length and 4m width - Dimension of welding unit and cooler: 4m length and 2m width - Min. and max. speed: from 90m/min up to 170m/min - Energy power from 76kwatt up to 120kwatt The line consists of the following parts: 1) Decoiler 2) Base machine 3) Welding unit EMMEDI 4) Cooling unit 5) Degreasing unit 6) Electronic flying shear 7) Exit Bench The groups of rollers available per type of product are as follows: For the production of bendable spacers with height 6,5mm: 5,5 8,5 9,5 11,5 14,5 15,5 19,5 Number of groups: 7 Number of auxiliary groups 7 For the production of normal (not bendable) spacers with height 6.5mm: 5,5 6,5 7,5 8,5 9,5 11,5 13,5 14,5 15,5 17,5 19,5 Number of groups: 6 Number of auxiliary groups 3 The aluminiu ...
Mitsubishi ML3015ex Laser Cutting Machine Year of construction 2012 Installation year 2013 Workpiece size 3050 x 1525 mm / max weight 950 kg Automatic pallet change LOAD MASTER loader Cutting Thickness: -Mild steel: 26 mm (oxygen) - Stainless steel: 12 mm (nitrogen ) - 10mm aluminum nitrogen (weather) Axle movement: X-3100mm / Y-1565mm / Z-150mm Fast travel speed: X ve Y - 100m / munite Fast travel speed: Z - 65m / munite Maximum feed 50m / munite 7,5 inç (2x) 7,5 inç auto focus head Automatic edge/plate detection (auto rotation) Mitsubishi 4500 Watt cross flow resonator (peak power of 5000W pulse) CO2 lazer CO2 / CO / N2 / He = 8/4/60/28 Laser gas consumption 3 liters / hour Double cut function allows surface removal and cutting on poor quality materials and shielded sheet metal Edge punching function Control of slag reduction in corners Retraction of the head wi ...
SEPARATOR BAADER, TYPE: 699 WITH FEED ELEVTOR AND OUTLET CONVEYOR Technical description: - Separator hopper with breaker and helicoid Dimensions: 2100 x 1050 x 1400 mm - Elevator for bins up to 200 liters Lift height: 2500 mm Dimensions: 900 x 750 x 3500 mm - Separator Baader, type: 699 Serial number: 12-7157-699 Year: 1989 Power supply: 380 V, 50 Hz, 15.0 A, 8.0 kW Drum holes: ? 2 mm Dimensions: 1500 x 1450 x 1550 mm - Outlet conveyor with plastic band Bandwidth: 200 mm Lift height: 900 mm Dimensions: 1500 x 400 x 950 mm This machine uses the same principle as the BAADER 694 and 697 but with much higher throughput. It is a further development of the BAADER 695. The speed is infinitely variable up to twice the normal speed. The belt pressure is controlled by a hydraulic system. Pressure and speed indicators allow correct adjustment of the machine to different raw material. T ...
Modular labeling machine 14 heads cold glue adhesive 8000 14 000 BPH This New modular labeling machine can be customized as needed Suitable for applying labels COLD GLUE AND ADHESIVES GLUE collar GLUE back U or L seal ADHESIVE front ADHESIVE back Bottles Containers CYLINDRICAL and SHAPED No labeling stations No 3 COLD GLUE groups N 2 adhesive groups 60 meters ON THE MODULAR TRAY Head diameter 960 mm Plates number 14 Min max label length 10 150 Min max label height 15 200 Container diameter height min max 30 80 mm Height 100 400 mm Max required speed 8 000 bph Basic machine composition 1 System built according to CE regulations 2 Machine operation via PLC Schneider 3 Touch screen control panel for labeler functions installed on a mobile and rotating support 4 Automatic variation of production speed with inverters and detection sensors installed on the conveyor belts 5 Light column indicat ...
Used Blow Moulding Machine Sidel SBO6 2 Year 2005 9000 bph The machinery has been disconnected from the functioning production The PLC is present and its functionality is ensured The machinery as a whole is in a good state of maintenance pre production maintenance is still recommended because the blow molding machine has been in storage for about 12 months Transport is a large load therefore outside the normal gauge We can supply all necessary spare parts for this blow molding machine [...for more information send your inquiry to the seller.] refno: SO81
Plug and play potato scrambler., TECHNISCHE GEGEVENS, - Capaciteit :± 450 kg per uur input. Afhankelijk van soort product, gewenste schrap/schiltijd, de kwaliteit van het product en snelheid van de operator., - Constructie : RVS 304., - Vulinhoud : ± 25 kg., - Maximale productdiameter : 150 mm.Capaciteit ± 100 – 600 kg. per uur afhankelijk van soort en kwaliteit van het product en de gewenste snijmaat, - Schakelkast : Geïntegreerd in machine., - Voeding : 400 Volt, 50 Hz, 3 fase + aarde + nul (Europese norm). 24 Volt op bedieningsknoppen., - Aantal motoren : 1, - Totale electriciteitsconsumptie : max. 1,1 kW/uur., - Aansluitwaarde : 3,3 Amp., - Stekker : 16 A CEE, 5 polig., - Waterverbruik : Max. ca. 450 ltr/uur (naar behoefte regelbaar)., - Luchtverbruik (alleen bij automaat) : Afhankelijk van schraptijd., - Gewicht : ± 200 kilo, onverpakt., - Keurmerk : CE genormeerd., Construc ...
Technical data of the bale opener line for RDF. MSW, paper, cardboard: Manufacturer Cross Wrap Oy Ltd, Siilinjärvi, Finland Type BO 4000 Year of manufacture 2015 Quantity of opened bales 674 pieces Operating time only 3 days, exclusively by running in the entire line during new installation Opening time approx. 45 seconds per bale Bale dimensions (W x H x L) 1100 x 1100 x 1400 - 1900 mm Max. Bale weight 2,000 kg Conveying height of the system 1,400 mm Max. Conveying width of the system 1,200 mm Material to be opened RDF/MSW Availability of the line 98% Noise level of the bale opener line 85 dB(A) Total connected load 37 kW Rated current 125 A Operating display SIEMENS SIMATIC HMI Touch Control SIEMENS S7 ET200S Installation dimensions 8,463 x 2,890 x 3,960 mm (l x w x h) Scope of delivery: Feed conveyor 3,500 x 1,200 x 1,400 mm Feed conveyor to opener 1,500 x 1,200 x 1,400 mm Bale opene ...
Technical data stationary waste compactor with weatherproof operator cabin Manufacturer Geesink Kiggen B.V. Type PD 26/20 Year of construction 2003 Pressing force normal 320 kN Pressing force during post-pressing 405 kN Theoretical capacity 350 m³/hour Cycle time approx. 27 seconds Volume bale chamber 2,6 m³ Volume per pressing cycle 2.2 m³ Press plunger flow in the container 320 mm Dimensions press plunger 740 x 1950 mm Filling opening 1,630 x 1,850 mm (L x W) Standard press opening for container 1250 mm Max. working pressure 330 bar Volume hydraulic tank 225 L Drive cable 11 kW Connection cable 5 x 4mm² Installation dimensions 4,300 x 2,495 mm Weight 3.500 kg Comments: We will not assume liability for the given technical data and possible errors.