used DEMAG for sale

Crane remote control, radio receiver, receiver, crane radio remote control, radio control system, crane control, radio remote control -Manufacturer: DEMAG Mannesmann Dematic, crane control PNN-BUS-3 -Type: RC-E 10 -Total dimensions: 380/180/H125 mm -Weight: 2.2 kg

Hand trolley, rolling trolley, crane trolley, trolley trolley, crane trolley, crane trolley, trolley, carrier trolley, monorail trolley -Crane chassis: beam width: up to 175 mm -Load capacity: 1000 kg -Dimensions: see technical. Drawing in the photos -Quantity: 8x chassis available -Price per piece -Dimensions: 245/200/H190 mm -Weight: 7.6 kg/pc.

Indoor crane, crane, electric wire rope hoist, hoist, motorized winch, motor winch, tackle, pulling winch, pulley block -Nominal load: 750 kg -Lifting speed: 9.5 m/min -Lifting height: 9.5 m -without service -Dimensions: 730/420/H340 mm -Weight: 160 kg

Indoor crane, crane, trolley, crane running gear, crane undercarriage, girder undercarriage, headcarriage for bridge cranes, ceiling crane headcarriage, headcarriage single girder bridge crane, headcarriage double girder bridge crane -Manufacturer: Demag, 1 set of end carriages for double girder bridge crane -Load capacity: 6400 kg -Drive motor: Mannesmann Demag 16I6 KF 8-2 0.15/0.60 Kw -Gearbox: Demag KS 7A -Support rollers: Ø 250 mm / groove width 70 mm, dimensions see photos -Dimensions: each 2850/515/H720 mm / approx. 270 kg -Transport dimensions: 2850/1030/H720 mm -Weight: 563 kg/total

Indoor crane, crane, electric cable hoist, hoist, motor cable winch, motor winch, tackle, pulling winch, pulley -Manufacturer: Demag, crane chassis with electric cable pull without remote control -Crane chassis: engine KBH125 B 2/12 3.60/0.53 kW -Cable: 4M DH 410 H12 -Load capacity: 2000 kg -Main stroke: 10.0 m/min -Fine stroke: 1.6 m/min -Hook path: 12.0 m -Dimensions: 1340/1300/H500 mm -Town weight: approx. 390 kg

Electric motor, three-phase motor -Power: 0.37 kW -Speed: 705 rpm -Shaft diameter: 24 mm -Construction: B5 -Protection class: IP 54 -Price: per piece -Number: 5x available -Dimensions: 290/170/H205 mm -Weight: 13 kg

Indoor crane, crane, trolley, crane running gear, crane undercarriage, girder undercarriage, headcarriage for bridge cranes, ceiling crane headcarriage, headcarriage single girder bridge crane -Manufacturer: Demag, 1 set of end carriages for single girder bridge crane -Load capacity: 6400 kg -Drive motor: Mannesmann Demag KBF 80 A 8/2 0.13/0.5 Kw -Gearbox: Mannesmann Demag AF05-M -0-1 -Support rollers: Ø 158 mm / groove width 65 mm, dimensions see photos -Dimensions: 2360/270/H660 mm / 178 kg each -Transport dimensions: 2360/540/H660 mm -Weight: 356 kg/total

Gear motor, electric motor, three-phase motor -Power: 0.55 kW -Speed: 110 rpm -Shaft: Ø 20 mm -Construction: B5 angle -Protection class: IP 54 -Number: 1x motors available -Price: per piece -Dimensions: 450/270/H175 mm -Weight: 20 kg

Gear motor, electric motor -Speed: 80 rpm -Power: 0.55 kW -Construction: B5 angle -Diameter shaft: Ø 20 mm -Protection class: IP 54 -Dimensions: 450/270/H175 mm -Weight: 20 kg

Electric motor, three-phase motor -Handover: in the current condition as seen -Brake: dismantled -Power: 1.8KW -Speed: 1375 rpm -Shaft: Ø 24 mm -Type: B5 -Protection class: IP 54 -Dimensions 360/200/H250 mm -Weight 19.5kg

crane remote control, radio receiver, receiver, crane radio remote control, radio control system, crane control, radio remote control, radio remote control -Manufacturer: NBB, radio remote control with charger -Type: SL 48-2/MOV HF:SM 430 -Charger: LAD 0470 -Total dimensions: 230/210/H170 mm -Weight: 3.2 kg

Gear motor, electric motor, stop motor, drive motor, crane motor, bridge crane -Manufacturer engine DEMAG type: KBA-112-MB-6 -Manufacturer engine DEMAG type: KBL-71-A4 -Manufacturer gearbox DEMAG type: FG08-B-14-U-0-H1- -Power: 0.3/2.9 kW -Speed: 106/945 rpm -Construction: B14 -Diameter shaft: Ø 28 mm -Protection class: IP 54 -Dimensions: 670/300/H500 mm -Weight: 102 kg

Injection molding machine, clamping force controller, control unit -Manufacturer: Demag Kunststofftechnik, closing force control device -Type: DMS-SKR 79/5 Id.Nr. 064 929 65RMS -Dimension: 165/95/H95 mm -Weight: 0.7 kg

Indoor crane, crane, electric cable hoist, hoist, motor cable winch, motor winch, tackle, pulling winch, pulley -Manufacturer: Demag, electric chain hoist with chassis -Type: PK1N load capacity 250 kg -Main stroke: 4 m/min -Fine stroke: 2 m/min -Transport dimensions: 600/500/H230 mm -Weight: 23 kg

Push trolley, push trolley, crane trolley, trolley trolley, crane trolley, crane trolley, trolley, carrier trolley, monorail trolley -Manufacturer: Demag, crane chassis -Beam width: up to 163 mm -Load capacity: kg -Dimensions: see techn. Drawing with the photos -Dimensions: 250/243/H180 mm -Own weight: 15 kg

Friction wheel, impeller, bridge crane, indoor crane, assembly crane, workstation crane -Friction wheel drive for: Demag crane -Impeller diameter: 270 mm -Impeller width: 90 mm -Number: 2x bikes available -Price: per piece -Dimensions: 390/120/H290 mm -Weight: 38 kg/piece

Gear motor, electric motor -Speed: 185 rpm -Power: 0.25 kW -Construction: B5 angle -Shaft diameter: Ø 15 mm -Protection class: IP 54 -Dimensions: 380/200/H150 mm -Weight: 14 kg

Column slewing crane, indoor crane, workplace crane -Manufacturer: DEMAG, pillar slewing crane load capacity 250 kg -Base plate: 550 x 550 mm -Projection: 2,860 mm -Total height: 5110 mm -Hook height: 3170 mm -Swivel range: 270° -Chain hoist: can be supplied at extra cost -Transport dimensions: 5110/800/H550 mm -Weight: 380 kg

Gear motor, electric motor, three-phase motor -Speed: 89 rpm -Power: 0.25 kW -Construction: B5 angle -Shaft diameter: Ø 15 mm -Protection class: IP 54 -Dimensions: 380/200/H150 mm -Weight: 14 kg

Column slewing crane, hall crane, workplace crane -Manufacturer: DEMAG, column slewing crane, load capacity 250 kg -Base plate: 375 x 375 mm -Throat: 3,040 mm -Total height: 3015 mm -Hook height: 2,100 mm -Chain hoist: DEMAG type PK2N-F -Main stroke: 10 m/min -Fine stroke: 2.5 m/min -Chain length: 2300 mm -Transport dimensions: 3090/800/H540 mm -Town weight: 203 kg

Column slewing crane, hall crane, workplace crane -Manufacturer: DEMAG, column slewing crane, load capacity 250 kg -Base plate: 450 x 450 mm -Throat: 4,060 mm -Total height: 3,515 mm -Hook height: 2,500 mm -Chain hoist: DEMAG type PK2N-F -Main stroke: 10 m/min -Fine stroke: 2.5 m/min -Chain length: 2800 mm -Transport dimensions: 4130/800/H500 mm -Town weight: 476 kg

Manipulator, lifting aid, lifting device, workplace crane, hall slewing crane, hall crane, workplace crane, material grab, column slewing crane -Manufacturer: dalmec, manipulator pneumatic Posivel type PVC -Load capacity: 80 kg -Throat: max. 3040 mm -Total height: 3015 mm -Hook height: 1800 mm -Stroke: 3300mm -Swivel range: 270° -Dimensions: see photo technical. drawing -Transport dimensions: 3050/700/H500 mm -Town weight: 192 kg

Crane magnet, lifting magnet, load lifting magnet, load lifting magnet, round magnet, scrap lifting magnet, scrap magnet -Construction: electro magnet -max lifting capacity: 2200 kg -Dimensions: 250/340/H460 mm -Own weight: 1114 kg

Indoor crane, crane, trolley, crane running gear, crane undercarriage, girder undercarriage, headcarriage for bridge cranes, ceiling crane headcarriage, headcarriage single girder bridge crane, headcarriage double girder bridge crane -Manufacturer: Demag, 1 set of end carriages for double girder bridge crane -Load capacity: 6400 kg -Drive motor: Mannesmann Demag 16I6 KF 8-2 0.15/0.60 Kw -Gearbox: Demag KS 7 -Support rollers: Ø 250 mm / groove width 70 mm -Dimensions: each 2850/515/H720 mm / approx. 259 kg -Transport dimensions: 2850/1050/H720 mm -Weight: 518 kg/total

Indoor crane, crane, electric wire rope hoist, hoist, motor winch, motor winch, tackle, traction winch, block and tackle -Manufacturer: Mannsmann Demag, electric chain hoist without chain and load hook -Type: PK1L -Load capacity: 125/250 kg -Main lift: 12/6 m/min -Fine stroke: m/min -Number: 1x chain hoist available -Price per piece -Dimensions: 230/200/H235 mm -Weight: 15kg

Indoor crane, crane, electric wire rope hoist, hoist, motor winch, motor winch, tackle, traction winch, block and tackle -Manufacturer: Mannsmann Demag, electric chain hoist without chain and load hook -Type: PK1N -Load capacity: 125/250 kg -Main lift: 4/2 m/min -Fine stroke: m/min -Number: 1x chain hoist available -Price per piece -Dimensions: 230/200/H235 mm -Weight: 15kg

Indoor crane, crane, electric wire rope hoist, hoist, motor winch, motor winch, tackle, traction winch, block and tackle -Manufacturer: Mannsmann Demag, electric chain hoist without chain and load hook -Type: PKV1-V1-F4 -Load capacity: 125/250 kg -Main lift: 8/4 m/min -Fine stroke: 2/1 m/min -Number: 2x chain hoist available -Price per piece -Dimensions: 230/200/H235 mm -Weight: 15 kg/pc.

Manual trolley, push trolley, crane trolley, trolley, crane trolley, crane trolley, trolley, girder trolley, overhead trolley -Transfer in current condition as seen -1x wheel missing (photos) -Friction wheel Demag type: 13/8RF8-2 -Barrier width: 120 mm -for narrow flange beams: IPE240 (120 mm wide) -The trolleys are pushed into a steel beam -Payload: 2000 kg -Number: 2x drives available -Price: complete -Dimensions: 2550/320/H350 mm -Own weight: 500 kg

Indoor crane, crane, electric wire rope hoist, hoist, motorized winch, motor winch, tackle, pulling winch, pulley block -Transfer in current condition as seen -Operation is missing a switching element (can be installed at an additional cost) -Motors tested: and ok -Rated load: 1125 kg -Lifting speed: 6.3 m/min -Lifting height: 6.3 m -Dimensions: 1100/1000/H700 mm -Weight: 368 kg

Gear motor electric motor -Speed: 197 rpm -Power: 0.55 kW -Construction: hollow shaft angle B5 -Diameter shaft: Ø 20 mm -Protection class: IP 54 -Dimensions: 460/230/H170 mm -Weight: 20 kg

Gear motor, electric motor, three-phase motor -Speed: 62 rpm -Power: 0.25 kW -Construction: B3 -Diameter shaft: Ø 25 mm -Protection class: IP 54 -Weight: 25 kg

Hydraulic power pack, hydraulic pump, hydraulic pump -Max. Pressure: 100 bar -Liter output: 6 l/min -Hydraulic tank -Hydraulic valve -Weight: 110 kg

Manual trolley, push trolley, crane trolley, trolley, crane trolley, crane trolley, trolley, girder trolley, overhead trolley -Demag friction wheel type: RF180 -Barrier width: 120 mm -Payload: 2000 kg -Number: 2x drives available -Price: complete -Dimensions: 2550/320/H350 mm -Own weight: 500 kg

This DEMAG Ergo-Tech 250-1450 injection moulding machine was manufactured in 1995. It comes equipped with handling capabilities, tailored for intricate and precise manufacturing processes. This machine represents a blend of durability and efficiency, making it a solid addition to any production line looking for versatile moulding solutions. The DEMAG Ergo-Tech 250-1450 we have for sale offers reliability and a robust build, ensuring longevity and consistent performance in demanding environments. For further details on this machine, please contact us.

This injection moulding machine was manufactured in 1999. The DEMAG D110-310H/120V stands out for its robust design and reliable performance over the years. Known for its efficiency in production environments, this model has been a staple for businesses seeking to enhance their manufacturing capabilities. This DEMAG machine we have for sale represents an opportunity to acquire proven machinery with a track record of success. For further details, please contact us to discuss how this machine can meet your needs.

This injection moulding machine, manufactured in 2000 by DEMAG, model Ergo-Tech 350 Concept, comes with handling technical specifications, making it a prime choice for efficient and reliable production. Its design emphasizes durability and ease of use, suitable for a wide range of injection moulding applications. The DEMAG Ergo-Tech 350 Concept machine we have for sale represents an opportunity to enhance your manufacturing capabilities with a proven, quality piece of equipment. For further information, please contact us.

This DEMAG Ergo-Tech 110-310H-120V injection moulding machine was manufactured in 2002, offering precision and reliability for various production needs. Its notable for its efficiency and ease of use, designed to streamline manufacturing processes. This DEMAG machine we have for sale represents a solid addition to any production line, enhancing output with its proven performance. Contact us for further details.

This used DEMAG Ergotech System 1500-440/120 injection moulding machine was manufactured in 1999, equipped with handling features for enhanced productivity and ease of use. As an injection moulding machine, it offers reliable performance and precision in moulding operations, making it a valuable asset for production lines requiring high-quality plastic components. The opportunity to buy this DEMAG Ergotech System 1500-440/120 injection moulding machine represents a strategic investment for businesses looking to upgrade or expand their manufacturing capabilities. For more details, please contact us.

This used injection moulding machine manufactured in 2001 by DEMAG, model D125-320h/120v, comes with handling features, designed to optimize production efficiency and reliability. A robust example of engineering excellence, this machine stands out for its precise performance and durability. The technical specifications highlight its adaptability to various production requirements, making the DEMAG D125-320h/120v machine we have for sale a valuable asset for any production line seeking quality and consistency. For further details, please contact us.

load 1.000 - 2.000,-kg. More then 300 machines new and second hand on our seema .de

Closing force: 280 T Opening stroke: 675 mm Between columns: 630 X 630 mm Tray dimensions: 950 x 950 mm Mini/maxi mould: 330/710 mm Max gap between trays: 1385 mm Motor power: 26 kW Heating power: 23.1 kw Type of control: NC 4

INJECTION UNIT Screw diameter: 60 mm Calculated injection volume: 763 cm³ Length / diameter ratio: 20 L / D Pressure on the material: 1905 bars PS plasticization capacity: 690 Kg / h CLOSING UNIT Closing force: 3300 kN Mold thickness Mini / Max: 330/710 mm Max distance between tray: 1385 mm Passage between columns: 710 x 630 mm Tray size: 1040 x 950 mm GENERAL Heat output: 55 kW Total installed power: 78 kW Quantity of oil: 700 l. EQUIPMENT - NC4 control - Electric motor on metering - Integrated hot ducts - EUROMAP - 3 Hydraulic cores - 3 Sequential cores - 1 Air core

Closing unit Clamping force [kN] 2000 Dimensions of mounting plates (hxv) [mm] 830 x 830 Clearance between columns (hxv) [mm] 560 x 560 Min./max. mold height [mm] min 310 Maximum opening width [mm] 1335 Injection unit Screw diameter [mm] 50 Injection volume [cm3] 451 Injection weight [g] 410 Injection pressure [bar] 1946 Electrical and hydraulic equipment Rated power of the pump motor [kW] 30 Heater power [kW] 15 Dimensions and weight Net weight with control cabinet [t] 9 Dimensions (length x width x height) [m] 5.7 x 1.7 x 2.1

Type of control: NC 4 Number of hours: 34,000 H Closing force: 80 T Opening stroke: 450 mm Between columns: 420 x 420 mm Tray dimensions: 600 X 600 mm Mini/maxi mould: 250/mm Max gap between trays: 700 mm Injection: Screw diameter: 35mm Screw length: 20 D cm3: 168 Bars: 2020 General: Motor power: 15 kW Heating power: 9 kw Cores: 1 Robot interface: yes Bi metal: yes

DEMAG 150T NC4 ERGOTECH 150/500-610 COMPACT 2 hydraulic cores 1 pneumatic core

Control type: NC 5 Number of hours: 27,000 hours Closing Closing force: 350 T Opening stroke: 700 mm Between columns: 760 x 710 mm Tray dimensions: 1070 X 1015 mm Mini/maxi mold: 400/670mm Max distance between trays: 1370 mm Injection: Screw diameter: 60 mm Screw length: 20 D cm3: 2366 Bars: 890 General: Motor power: 55 kW Heating power: 23.1 kW Closing weight: 18 T Injection weight: Dimensions length: 6.5 m Width dimensions: 1.8 m Dimensions height: 2.3m Options: Cores: hydraulic predisposition 2 cores Robot interface: E67 Bi metal: YES Others: 4 blow guns, 2 Kisler mold pressure ports, laminar flow, 8 hot runners

Were parting with our 2 injection molding machines following a reorganization of our workshop. The 1st press were selling is an Engel 200/50 HL-ST (photos in attachment), which works well but has a few jerks during the injection phase, but is functional. The 2nd press is a Demag Ergotech 150-600 (photos in PJ), which works but has a few problems, and can no longer be considered a 150T but rather a 90T (pump wear).

Control type: NC 4 Number of hours: 32,500 hours Closing force: 80 T Opening stroke: 450 mm Between columns: 420 x 420 mm Tray dimensions: 600 X 600 mm Mini/maxi mold: 250/mm Max distance between trays: 700 mm Injection: Screw diameter: 35mm Screw length: 20 D cm3: 168 Bars: 2020 General: Motor power: 15 kW Heating power: 9 kW Closing weight: 4 T Injection weight: Dimensions length: 4.2 m Width dimensions: 1.4m Height dimensions: 4.8 m Options: Cores: 1 Robot interface: yes Bi metal: yes

The machine has a Demag DR631-0399 robot built into it. Machine with CE standards. Type of material used: PC/ABS Service History: 3.2018 - Calibration - Ergocheck 1.2016 — Replacement of a faulty hydraulic system pressure sensor. scheme 1.2015 – repair of the nozzle rod. units 2.2014 — Replacement of the chamber, auger and tip 1.2013 — Replacement of the screw and tip 6.2012 – Repair, re-sealing of the injection cylinder. units 11.2010 — Repair of proportional valve 4.2008 — Replacing the control panel display 3.2008 — Replacing the proportional valve 3.2008 — Calibration — Ergocheck 12.2007 — Replacing the tip

Clamping force [kN] 1600 Dimensions of mounting plates (hxv) [mm] 770 x 770 Clearance between columns (hxv) [mm] 520 x 520 min./ max. mold height [mm] min275 max 685 Maximum opening width [mm] 500 injection unit Screw diameter [mm] 40 Injection weight [g] 260 Injection pressure [bar] 1600 Electric-hydraulic equipment Nominal power of the pump motor [kW] 22 Heater power [kW] 11.3 Dimensions and weight Net weight with control cabinet [t] 6.5 Dimensions (L x W x H) [m] 5.3 m x 1.5 m x 2 m