Fabricante:
(Categoría: 1300)
SEKWANG Shot Machinery Co. Ltd SKHSS-4600 PRE-TREATMENT SYSTEM (2006) Including: -Main Pre-treatment system -Main control panels -Conveyor -Compressor -Dust and Fume Collector -Pre Heater -Shot blasting -Vacuum Recovery -Welding Machine -Blower -Mixing room Including an assortment of spare parts : Bearings Chain Belts Manganese Filter Sacks, etc. Make SEKWANG Shot Machinery Co. Ltd Model SKHSS-4600 Year 2006
RUDDER TRANSPORTER HYUNDAI HYDRAULIC CO. LTD Hyundai Hydraulic Co. Ltd. Rudder Transporter (2009) Size: 6410 x 7220 x 6995h Capacity: 200Tons Weight: 76.5Tons Frame up/down Capacity: 100T x 4set Stroke: 1500mm Speed: 180mm/min Driving Driver: Hydraulic motor Swing: Manual 5, 15, 30, 45, 90 deg. Speed: 1~6 M/min Working table Capacity: Pushing: 44T x 2 set Pulling: 28T x 2 set Stroke: 500mm x 2 set Working Table Sliding Capacity: 50Tons Stroke: 1300mm x 2step x 2set Table size: 1900 x 5650 mm Rudder Clamping Capacity: 65Ton x 4set Stroke: 650mm Hydraulic Pump type: Tanbem Gear Pressure: 210Kg/sq.cm Tank: 400L x 2set Hose: Connect type Electric Main: AC440V x 3P x 60Hz Control: AC220V x 1P x 60Hz Weight: 76,50 Capacity: 200 Make Hyundai Hydrau ...
2684 kW ‘’SAMKWANG’’ (2010) 2 CUMMINS Engines 1342 kW each; Gross/Net tonnage 314/94; L X B X D: 30.59 x 9.40 x 4.20 M Hull Material: Steel Draft: 3.627 Meter Fuel Capacity: 91,504 L Maximum Speed: 13 Knots Cruising Speed 11 Knots Engine Horsepower: 1,800 HP each Engine Cycle: 4 SN: 33180913/33180861 Auxiliary Engine: 2 Emergency Generator: 1 Model: Hull No. SKSB188 Capacity: 10 crews Make SAMKWANG SHIPBUILDING & ENG'G. Serial 00-0000778 Year 2010
Unused and not yet fully assembled two-chamber industrial washing machine, is offered very far below original price! Technical data according to manufacturer's specifications: Dimensions Width = 3278 mm Height = 3350 mm Depth = 3924 mm Weights Total weight = 6500 kg Ab. Gross batch mass = 500 kg Required floor load capacity = 1500 kg/m² Washing medium Operating medium = demineralized water Water connection = 4 bar, 3/4", cold Working temperature range = 10 -70°C, adjustable Flood pumps = 2 centrifugal pumps, flow rate per pump approx. 2 mn³/min, connected load per 4 kW Water Quantity Washing Process Chamber 1 = 3.9 m³ Water level measured from above Water level chamber 1 = max. 250mm, nominal 100-200 mm, min. 50 mm Heating Heating basin = 10 cartridge heaters, electric Total connected load = 85 kW Nominal voltage = 3 x 400 V AC~ PEN Control volta ...
Nilfisk T30S, item number 4030600083 3.0 KW, 400 V, 50 Hz, 2840 rpm, 3 phases, 6.6 A, cos phi 0.90, Iso F, S1, IP55 Weight 103 kg, container volume 100 liters Vacuum -220 mbar, 130 m³/h Overpressure 278 mbar, 120 m³/h Year of construction 2011 ... más información
Angle gearboxes / gearboxes NOSEN type. RN-4 M-I-LR-1:1 T shape / 1 shaft input - 2 wave outputs -Shaft diameter 19 mm -The ratio of i = 1:1 -Speed max 1500 rpm -Weight 10 kg -Max. Of torque at 1500 rpm: 31.9 NM used from inventory. ... más información
Angle gearboxes / gearboxes NOSEN type. RN-6 M-I-LR-1/1 T shape / 1 shaft input, 2 outputs of waves -Shaft diameter 25 mm -The ratio of i = 1:1 -Speed max 1500 rpm -Weight 23 kg -Max. Of torque at 1500 rpm: 96 NM ... más información
1 post PILZ safety relays, a total of 46 units, consisting of: 1.Pilz PNOZ1 (for emergency stop and protection doors), ID 475695: 5 piece 2.Pilz PNOZ (for emergency stop and protection doors), tag 474695: 5 piece 3.Pilz PNOZ 5(NOT-AUS-Schaltgerät), tag 474590: 1 piece 4.Pilz PNOZ 8 (for emergency stop and protection doors), tag 474760: 1 piece 5.Pilz PNOZ X 2.1 (for emergency stop and protection doors), tag 774306: 1 piece 6.PILZ PNOZ X 2 (for emergency stop and protection doors), tag 774303: 1 piece 7.Pilz PZE 9 (contact expander module), tag 774150: 5 piece 8.Pilz PZE X4P (contact expander module), ID 777585: 1 piece 9.Pilz t & a 5V (guard door monitoring), tag 474965: 1 piece 10.Pilz PNOZ X 7 (for emergency stop), tag 774059: 1 piece 11.PILZ PNOZ X8P, tag 777760: 5 pieces, (for emergency stop, safety doors and light barriers) 12.Pilz PNOZ X3P, ident 777310: ...
Used Hydropneumatic Press / Assembly Press - Pressing force 10 KN (1 to) - Used hydropneumatic cylinder make TOX - Pneumatic two-hand control - Portal frame aluminum profile 90 90 mm - Machine table made of aluminum profiles and multiplex plate 700 700 mm - Total weight approx. 50 kg Suitable as an assembly press for insezing components. With x- and y-adjustment alignable vice for die diameters up to 80 mm. Or for small punching or embossing tools. All tools or vices are quickly changed through the groove system.
Test press for single-axial pressure tests from 0 to 10 KN (0 to 1,000 KG) Purpose: Test press for single-axial pressure tests from 0 to 10 KN (0 to 1,000 KG / 10 KN maximum load). Without distance measurement. Manual lifting spindle press - Static pressing force 5 KN (0.5 to) - Portable, stable press frame made of polyamide PA 6G - Manual spindle stroke gearbox with spindle 20 mm, incline 5 mm - With handwheel diameter 120 mm and handle - Gearbox reduction 1: 10, per handwheel revolution 0.5 mm spindle path - This requires only very low hand force. - Table size 235 195 mm - Light width 190 mm - Stamp size diameter 70 mm - With 4 holes 8 mm for fixing a larger stamp plate - Very easy to operate by spindle and worm gearbox - Total weight approx. 25 kg Force measuring device: Weighing module with shear rod load cell for nominal load 1,100 kg. ...
Ball-lock pins d = 10 mm Wearing length 50 mm Stainless steel with 2 balls 40 pieces in stock ... más información
Make: Kockum Sonics AB Item: Signal Controller Model: TLI 50 E-2 Condition: Unused surplus unit as good as New- Without Box ... más información
Cat.-No. 14.00230 in very good condition Cat.-N°: 14-00230L available: 1 unit 115 m tube in AISI 304 DN 40 Mount according to your Specifications Other Sizes upon Request Measurement and weight: total height: 400 mm Width: 700 mm total length: 3000 mm weight: 185 kg All prices are valid Ex-Works, excl.VAT Freight Charges: depending on dimensions and destination Delivery: from D-97753 Karlstadt-Karlburg Subject to prior sale General terms and conditions listed on our website. Prices are subject to change without notice. Visit our Web-Site: www.eurolux-ag.com
Cat.-No. 15-00086 new Measurements and Weight: Height: 1100 mm Length: 2150 mm Width: 820 mm Weight: 100 kg All prices are valid Ex-Works, excl.VAT Freight Charges: depending on dimensions and destination Delivery: from D-97753 Karlstadt-Karlburg Subject to prior sale Visit our Web-Site: www.eurolux-ag.com
Cat.-No. 15 00059 new Measurements and Weight: Length: 1730 mm Width: 570 mm Height: 1340mm Weight: 300 kg Characteristics of the drive: Spur gear transmission: - Transmission 38 /min Screw rotational speed (output speed) 12-50 /min Electrical Data: - Power 5,5 kW - Rotational speed 1450 /min - Current consumption ~ 11A - Voltage 3/PE/400 V - Frequency 50 Hz Machine power: max. 80 kg/h of purifies rape seed Operating Instructions available All prices are valid Ex-Works, excl.VAT Freight Charges: depending on dimensions and destination Delivery: from D-97753 Karlstadt-Karlburg Subject to prior sale Visit our Web-Site: www.eurolux-ag.com
Cat.-No. 15-00071 new for sterile aseptic warehousing and outsourcing for KZE Tanks KZE-fitting complete connection DN 40 right – 90° bow welded filter and butterfly valve DN 15 180° bow double pipe clamp DN 40/15 Air G-DN 25 li-FSV G-DN 25 DIN 11864 for gases 0,5 bar lifting device + cleaning Below SV DN 40 VA – Handle at the front manometer up K/M DN 40 AISI 304 Weight: 8 kg Surcharge for filter cartridge Pall Emflon 0,2 € 100,-- All prices are valid Ex-Works, excl.VAT Freight Charges: depending on dimensions and destination Delivery: from 97753 Karlstadt-Karlburg Subject to prior sale Please visit our Web-Site: www.eurolux-ag.com
Kat-nr. 14-00134 in very good condition Description available Fabr.-No. 1992 Type: VELACART B750 - 16H07 DN 080 Built: 1991 Filter insert: Candle Liquid: Gas: permissible operating overpressure (bar) 10 10 Container permissible operating temperature (C) 85 85 Room capacity: Container (l) 105 Clamping screws type M20X85A2 Manufacturer: 2 Dimensions and weight: H x W: 2000 x 800 mm Weight: approx. 165 kg All prices ex works plus legal Vat Intermediate sale reserved Delivery: from Karlstadt-Karlburg location - freight costs: according to delivery
Cat.-No. 13-0291 in a very good condition Testing water by 22°C back pressure at 1 bar Pressure: 6,0 bar capacity: 6600 litres/h motor: 220 V, 380 A, 3,0 kW Connection: inlet/outlet: DN 80 according to DIN 32676 - can be changed on request for an additional charge surcharge: infinitely via frequency converter Measurements and weight: length: 1200 mm width: 400 mm height: 1050 mm weight: appr. 250 kg All prices are valid Ex-works, excl.VAT Freight Charges: depending on dimensions and destination Delivery: from 97753 Karlstadt-Karlburg Subject to prior sale
Cat.-No. 13-0290 in very good condition Operating pressure test at 2.0 bar Test medium: water at 22 ° C at 1 bar pressure Capacity: 2400 l / h Engine power: 2.20 kW, 50 Hz Connections: inlet and discharge pressure DN 65, thread according to DIN 32676 -can be converted against extra charge With frequency inverter infinitely variable (surcharge) on request Dimensions and weight: Length: 850 mm width: 380 mm height: 770 mm weight: 125 kg Note: 100% pump all prices apply ex works plus gesetzl.MwSt tested with warranty. Delivery: from 97753 Karlstadt Karlsburg freight expenses: reserved to standard equipment sale
Cat. No. 13-0044 in a very good condition Typ: BN 3101 131 424 Testing water by 22°C back pressure at 1 bar Pressure: 1,1 bar capacity: 10.800 litres/h Motor: 1,8 kW Connection: inlet/outlet: DN 65 according to DIN 32676 can be changed on request for an additional charge Measurements: length: 96 cm width: 33 cm height: 100 cm weight: 84 kg For more Information please contact us under: Phone +49(0)9353-909050 Fax: 09353-9090522, Mobile: 0171-6518248 Subject to prior sale. All prices are valid Ex-Works, excl.VAT. Freight Charges: depending on dimensions and destination.