cepilladoras usadas para la venta

WEINIG four-sided planing machine, PM 17, 5 spindles Machine No. 1329-2356 Year of manufacture: 1982 Working width 170 mm Planning height 120 mm 5 spindles: max. tool length 180 mm, 130 mm Feed table length 2000 mm with planing heads 6 spindles arrangement: 1. Bottom 4 kW 2. Right 3 kW 3. left 5.5 kW 4. Top 5.5kW 5. Bottom 4kW / universal Spindle diameter approx. 35 mm Feed speed 6.5 - 49 m/min. manual lubricant pump Incl. 5 tools for all heads Dimension 4500 mm x 1300 mm x H 1500 mm Weight approx. 3800 kg Technical data subject to correction

WEINIG planer/moulder Unimat 22A with 9 heads Year of construction: 1987 Serial number 222-896. The planer is in good working condition and has been partially overhauled, cleaned and subjected to careful technical controls. • The machine has been thoroughly cleaned and technically checked. • Some wear parts have been replaced. • A test run was carried out to ensure functionality. • The machine is bolted to a wooden structure and is ready for shipment. • The planer and moulder is equipped with all the tools and is sold as such. Further technical data of the machine: Maximum planing width: 220 mm Maximum planing height: 140 mm Diameter of the spindles: 40 mm Spindle speed: 6000 rpm Length of the inlet table: 2 m The machine has a total of 9 spindles with the following configuration: 1. Lower spindle / dressing spindle : 5.5 kW 2. Right spindle /  ...

Planer and moulder Wadkin GA220 with 9 spindles Year of construction 1980 Maximum size of the approved wood 230 x 130 mm Maximum size of the finished wood 220 x 120 mm Configuration: 1. Spindle Bottom 2. Spindle Right 3. Spindle Links 4. Spindle Right 5. Spindle top 6. Spindle Bottom 7. Spindle Top 8. Spindle Bottom 9. Spindle Universal Most engines are 5.5kW and 7.5kW / 11.0kW Feed speeds variable 6- 36m/min Feed roller diameter 140mm Spindle diameter 40mm Spindle speed 6000 / 9000 opt. RPM Straightening table 2,0m max clamping removal 10mm technical information subject to reservation

Gubisch planer and moulder 172/7 S/N 3425 80 Year of construction 1980 Length of the dressing table 1950 mm Planing width maximum 170 mm Planing height maximum 120 mm Spindle diameter 40 mm 7 planing shafts : 1.Bottom dressing shaft 7.5 kW 2.Right joining shaft 3.0 kW 3.Left wave 4.0 kW 4.Right shaft 4.0 kW 5.Top Thickness shaft 4.0 kW 6.TopDickenhaft 5.5 kW 7.Uniwelle top / bottom 3.0 kW Voltage 380 V, 50 Hz Power consumption 33.6 Kw Feed motor 1.5 kW Feed speed infinitely variable 5 – 30 m/min. Weight 3300 kg Dimensions ( L X W x H )4800 mm x 1400 mm x 1850 mm technical information subject to reservation

Thickness planer Casadei R51/ H3 Year of construction 1997 Manufacturer Casadei / Busselato Italy S/N 97-61-053 Working width: 510 mm Working height Max.: 300 mm Workpiece length min.: 250 mm Working height min.: 4 mm Maximum cut depth: 8 mm Table length: 860 mm Variable feed speed : 6 / 9 / 14 /22 m/min Knife sizes 4 pieces 510 x 35 x 3mm ( standard knife ) Knife head diameter: 120mm Knife head speed RPM 4600 Main motor: 5.5 kW Dimensions: 1120x960x1250 mm Weight: 643 Kg Electromotive height adjustment Feed roller on the table

Specifications Spindles: 2 Spindle arrangement: Bottom (5.5 kW) – Top (5.5 kW) Working width: 220 mm Working height: 120 mm Feed: 3 kW // 32 m/min Spindle diameter: 50 mm Jointer Counter bearings Short Parts Package ... más información

WEINIG HYDROMAT 22 BL Year of construction 1995 with splitting unit (lamellar saw) Feeding (Automatic feeder and pull-out unit!) With safety hood and soundproof cabin! Machine specifications:  - Planning capacity 220 x 120 mm  - Feeding, 8– 80 m/min, motor 18.5 kW Spindle layout:  Bottom-right-left Top - bottom, table rigid Bottom, table rigid, spindle prepared Top - bottom, table rigid, spindle prepared Gap unit, consisting of 1 right and 1 left spindle each 30 kW (4500 rpm) incl. table roll, sliding roller, spray barrier and gap wedge removal 4 roller pull-out Special pressure and fixtures for the production of top layer slats Feeder (all-in) for slats and pull-out tape     

Weibert FS 32 Dressing thickness planer Planing width 320 mm 3-reversible planer knife shaft HSS Motor 3kW 400V 50Hz Passage height: 4-225mm Numerical display of the planing height Planed dressing and thicknessing tables WJ-300100  ... más información

Technical details: - Max. planing width: 500 mm - Maximum chip depth: 5 mm - Length of feed table: 1,300 mm - Length of the take-off table: 1,500 mm - Total length of the table: 2,800 mm - Table height: 800 mm - Max. workpiece length without support: approx. 1.5 m - Length of the joining fence (Aigner joining fence with integrated auxiliary fence): 1,300 mm - Height of the joining stop: 150 mm - Joining stop adjustable up to 45° and extendable over the entire width of the table - Diameter of the TERSA knife shaft: 125 mm - Nominal speed of the TERSA knife shaft: 5,000 rpm - Number of planer blades: 4 pieces - Minimum width of planer blades: 17 mm - Diameter of suction nozzle: 160 mm - Required air velocity: min. 20m/s - Required air volume: 1500 m³/h - Vacuum at 20m/s air velocity: 705 Pa - 6 x machine shoes with adjustment screws - incl. EMERGENCY STOP switch En ...

Weibert fs 52es SPIRAL Dressing thickness planer Planing width 520mm Spiral knife shaft Dressing table length 2250mm Planer fence 1500mm 90°-45° Machine Grey Cast Iron Tables 7 KW (9.5 HP) 400V 50 HZ Thickness table 850x520mm Passage of 3 / 240mm 4 feed speeds 5 / 8 / 12 / 18 m/min Dual folding system of the tables to the rear max. chip removal 5mm Speed 5000 min/1 1 extraction connection 120 mm Weight approx. 700 kg G&STÜ-5503502

From insolvency: Mafell ZH 300 K 380 volts 3500 watts of power Planing width 300mm Machine no.352867  ... más información

; as new  ... más información

planing width 630 mm planerhe 200 mm, motorized adjustment 4 - Meswser shaft, connection 7.5 kW, weight 1.5 t; unmaintained  ... más información

Weibert SD 510 Dressing thickness planer including spiral knife shaft Planer width 510mm Dressing table length 2250mm Planer fence 1500 mm 90°-45° Machine Grey Cast Iron Tables 5.5 KW (7.5 HP) 400V Thicknessing table 1050 x 510mm Passage of 250mm Numerical display thickness table Electric height adjustment of the thickness table 2 infeed speeds 6 & 12 m/min Dual folding system of the tables to the rear Weight of 900 kg G&RO-SD510NE-SPIRAL

Weibert SD 510 Dressing thickness planer including 4-tersa knife shaft Planer width 510mm Dressing table length 2250mm Planer fence 1500 mm 90°-45° Machine Grey Cast Iron Tables 5.5 KW (7.5 HP) 400V Thicknessing table 1050 x 510mm Passage of 250mm Numerical display thickness table Electric height adjustment of the thickness table 2 infeed speeds 6 & 12 m/min Dual folding system of the tables to the rear Weight of 900 kg G&RO-SD510NE-TER

Technical details: - Max. table width: 630 mm - Max. table length: 1,050 mm - Max. planing width: 630 mm - Max. planing height: 250 mm - Diameter of suction nozzle: 140 mm - Diameter knife shaft: 120 mm - 4 x strip planer knife, 820 x 35 x 3 mm - Knife shaft speed: 5,000 rpm - Manual star-delta switching - 2 feed speeds, 9 + 18 m/min (manually adjustable) - Thickness table adjustment manually via handwheel and analogue display (scale) Accessories: - 1 x "BARKOMAT" magnetic tool set for adjusting the planer knives Engine data: - Voltage: 380 V - Current: 16.8 A - Frequency: 50 Hz - Power: 7.5 kW (10.0 hp) - Speed: 2,860 rpm - Feed motor power: 0.9/1.3 kW Dimensions (LxWxH): 1,450 x 1,300 x 1,400 mm (incl. extraction nozzle) Transport dimensions (LxWxH): 1,200 x 1,450 x 1,500 mm (on EURO pallet) Weight: a. 950 kg The machine has been completely cleaned, ove ...

I sell the Weinig Unimat 300 four-sided planer, built in 2004 Feed speed 5-30 m/min. Working width 230mm Working height 130mm 5 Spindle Configuration: bottom - right - left - up - down Combined power 28kW 3-zone pneumatic pressure Good condition. Fully operational! Available soon. Includes full documentation and CE certification.

SCM moulder model SUPERSET 23 with 5 shafts: - Useful working dimensions 230x120mm - Alfasistel electronic control for 2-axis programming - Cardan drive and differentiated pneumatic pressure - Variable feed speed from 4 to 26 m/min - feed unit before the 1st shaft, with quick override - drive roller in the plane after the 5th shaft - 2500mm entrance level - Deck lubrication pump - shafts D=40mm at 6000rpm - Complete with 4 knife heads Trees: - Under HP -right - Left (right+left with single HP engine) - Above HP - Under HP

The machine contains the components from the large-scale series of the powerful WEINIG class Working width 20 – 260 mm / carpentry version Working height 8 – 160 mm 5 working spindles DM 40 mm Long inlet work table - 2000 mm 5 working spindles, bottom 5.5 kW, left + right 7.5 kW, top 7.5 kW, plaster bottom 11 kW Pneum. Pressure of the feed rollers Cardan feed infinitely variable 5 – 24 m/min. ATS system: Up to 98 workpiece dimensions can be programmed and called up at the touch of a button Left and upper spindle drive auto. in position Machine in CE design Built in 1998 Without editing tools

SPECIFICATIONS Pre-planer mm: 2000 Number of spindles: 5 Spindle configuration: I below - week 5,5 II - III right- left - KW 7,5 IV above - week 5,5 V below - week 4,0 Cardan shaft Speed-controlled drive KW: 4.0 Spindle diameter mm: 40 Revolutions per minute: 6,000 Max. working width mm: 230 Max. machining height mm: 120 Complete with: - Soundproof cabin - Grooved table -Tools CE-compliant