Fabricante:
(Categoría: 307)
clamping force: 450 kNinjection volume: 99 cm³screw diameter: 30 mmplaten size: 860 x 320 mmclosing stroke: 406 mmCondition: used,Specification: C-Frame Injection Moulding Machine - second-hand Serial No.: 45083Clamping unit:- Clamping force: 450 kN- Opening travel: 406 mm- Heating plate size: 860 x 320 mm- Mould height min.: 264 mm- Max. plate spacing: 464 mm- Ejector stroke: 20 mm- Ejector force: 20 kNInjection unit:- Screw diameter: 30 mm- Screw length L/D: 16- Dosing stroke: 140 mm- Stroke volume max.: 99 cm³- Max. spray weight: 114 g- Screw speed: 20 - 300 rpm- Injection flow: 106 cm³/s- Injection flow increased: 71 cm³/s- Special injection pressure: 1451 bar- Spec. injection pressure increased: 2205 bar- Nozzle path: ...
Panstone 800ton Press Slabside type, Single Station Manufacturer: Panstone Main ram diam. 14” x 4pcs (200ton x 4pcs) Clamp Force 800 Ton Max Piston Diameter 600 mm diameter Working Pressure 210 kg/cm2 Stroke Max 600 mm Daylight Max 600 mm Electric Heating platen size 2500x2500 Heater Capacity 34.8 KW Oil Reservoir 870 l Year of Manufacture 2010
Maplan Injection Moulding Machine Model: MTF400/80C 80 Ton Safety distance 162mm Run-on time 81ms Follow-up 5mm Pattern size 510mm x 410mm Touch screen control Year 2010 ... más información
cross-section width:: -- mmcross-section heigth:: -- mmfeed:: -- mmspeed of feed:: 0,4 - 20 m/minThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG. ... más información
clamping force: 350 kNinjection volume: 58,5 cm³screw diameter: 28 mmplaten size: 260 x 254 mmCondition: used,Specification: injection moulding machine for TPE - usedclamping unit:- clamping unit: vertical- clamping force: 350 kN- opening stroke max.: 300 mm- platen distance max.: 500 mm- Mould installation height min.: 200 mm- Clear width between tie bars: 260 x 254 mm- Ejector stroke max.: 80 mm- Clamping unit: VV- Lift of protective bonnet: 500 mmInjection unit:- Screw diameter: 28 mm- Screw L/D ratio: 18.6- Screw stroke max.: 95 mm- Injection volume max.: 58.5 cm³- Injection pressure: 1577 bar- Plasticising flow: 8.6 g/s- Injection flow: 85.5 g/s- Connected load: 3x 400 V, 50 Hz- Max. heating power: 5.8 kW- Drive power: 7,4 kW- Total power: ...
machine measurements: 2.200 x 1.200 x 2.260 mmmachine weight: 1.000 kgpower capacity: -- kWCondition: usedSpecification: automatic control machine for O-rings - second-hand rotary transfer machine with 16 pick-up stations- year of construction approx.: 2011 - pick-up stations: 16- measuring range: ID from 55 - 90 mm cord from 2,5 - 3,5 mm (ID 55 - 70 mm) cord from 2.5 - 4.5 mm (ID 70 - 90 mm)- Part throughput: approx. 3 - 4 seconds per part approx. 900 - 1,200 parts per hour approx. 21,600 - 28,800 parts per day- Technical application: surface defect and crack detection on O-rings- Sorting function: Good, Bad, Undefined- Dimensions LxWxH approx.: 2,200 x 1,200 x 2,260 mm- ...
Wind-u for AUMA / Rotocure, Calender,.. transportable, plug and play E+L centering ... más información
Qty 1 x Carter MK6 direct drive Banbury internal mixer, Serial no. 237/11 (New chamber/hydraulic hopper in 2011/12), Hydraulic hopper, Chamber volume: 160L, 2 wing rotors, SSA type dust stops, hydraulic drop door with linear actuator, pneumatic oil injector fitted to end frame, hydraulic hopper, PIV semi unidrive gearbox (28:1 ratio), 310/620kW power rating, 728/1484rpm input speed, 26/53rpm output speed. Currently fitted with fixed speed motor fitted - 355kW, 744rpm to give rotor speed 26.5rpm. Complete with lubrication unit, hydraulic unit, electrical controls etc and in very good condition (inspection report carried out by Farrel available on request).
Pattern Making Router for composite mould tooling CMS Athena 5 Axis Router Manufacturer: CMS Industries Model: Athena 2015 Z 800 Six station tool changer Uses HSK63 tool holders. A set of 6 holders with various gauge lengths included With new un-machined table Blower type vacuum pump Powered through a normal red 3 phase plug Year 2011 In full working condition and regularly serviced
clamping force: 11000 kNinjection volume: 12500 cm³screw diameter: -- mmplaten size: -- mmCondition: used,Specification: injection moulding machine for rubber - used, in very good condition machine was serviced annually by manufacturerclamping unit:- Euromap (size): 11000-25600- clamping force: 11.000 kN- size of heating platens L/W/H: -- x -- x mmInjection unit:- Injection volume max.: 12,500 cm³- Injection pressure: 2050 bar- Dosing force: 118 kN- Control: Siemens S7- Connected load: 3x 400 V, 50 Hz, N- Total current: 276 A- Back-up fuse: 300 A- Pump drive: 277 bar- Driving power: 45 kW- Weight approx.: 43.8 tOperating hours approx.: 33,130 hoursThe data for this ad was created with ModulMWS - t ...
Automatic hardness testing device with 4 heads Micro IRHD IRHD Type L IRHD Type N IRHD Type H The device needs gibitre software installed on the computer to work. The device consists of a stand and 4 heads ... más información
Automatic hardness testing device with 3 heads Shore 00 Shore A Shore D The device needs gibitre software installed on the computer to work. The device consists of a stand and 3 heads ... más información
A rotational shear viscometer according to Mooney for performing Viscosity tests (ML / MS 1+X), Stress Relaxation testing, Mooney Scorch, Delta Mooney testing on polymers as well as rubber compounds for quality control, research and development applications. ... más información
Machine number 205557/2012 Without softwear! Head failure! ... más información
Bainite (India) model BMPX150 PIN type cold feed extruders, Year of manufacture 2013 Screw diameter: 150mm L/D ratio 16:1 Output: 1200 - 1500kg/hr Power roller feed (opening 175mm), provision for cooling, Screw speed: variable max 50rpm, Max operating pressure: 340bar (5000psi) 10 rows of 8 pins (80 total) With 210kW Siemens AC v/s motor through 28:1 reduction gearbox (service factor 1.75) Hinged extrusion head with C'clamp suitable for strip All mounted on a fabricated steel base Complete with electrical controls and VFD (Siemens make). Safety features as per European standards.
available GK-190-E as option available Gear Box, Set of Spare Rotors, DC Motor ... más información
It is used in rubber and plastics mixing, warming mixing, sheeting mixing, etc. III Equipment specification XK400×1000 mixing mill 1. Main technical specification NO. Item Main technology data and feature A Main technology data 1 Roll diameter 400mm 2 Roll working length 1000mm 3 Roll linear speed Front:14.85m/min Rear:18.85m/min 4 Speed ratio of rolls 1:1.27 5 Max roll space 10mm 6 Compound feeding capacity 25kg-35kg 7 Motor power 37KW,n=980r/min,IE3 8 Dimensions 4400X1710X1850mm 9 Gross weight 8500kg B Feature of main machine 1 Roll size(mm) Ф400×1000 material alloy chilled hard cast iron, surface hardness HS70±2,Surface roughness: Ra0.2 Bearing type Adopt the aligning roller bearing, copper pressure ring, bearing taper 1:12 type Front roll is drilled roll and rear roll is drilled roll, can pass cooling water, e ...
LWB Steinl Injection Moulding / Vulcanizing Press Model: VCEFE Clamping force 2500kN Injection volume 1000 cm3 Compressed air 6 bar 76 kW Hydraulic oil 46/40 cst Pattern size 760 x 630mm LWB Flex touch screen Qty 2 Tool Kemp model TT-188 Year 2013 Weight 13500 kgs ... más información
QTY 1 x TMP (Division of French Oil, USA) Techni-Mix Lab Mixer, Model HD-5, Year of manufacture: 2014 (New), CE Marked, Mixing capacity: 5 Litre, 2 wing tangential rotors, Pneumatic hopper, Tilting body discharge (easy for cleaning), 20HP AC variable speed motor, Rotor rpm - Front 47.55rpm, Rear 39.28rpm. Complete with Electrical controls and in excellent condition.