prensas usadas para la venta

pressure: 63 tthroat: 320 mmstroke: 8-100 mmno. of strokes: 120 Hub/minram - range of adjustment: 63 mmtable surface area: 860x620 mmram surface: 540x360 mmhole in the table: Ø 270 mmtable height: 850 mmtool hole in ram: Ø 50 mmweight of the machine ca.: 5,5 tdimensions of the machine ca.: BxTxH 1500x2000x2700 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Inv. Num. : 5698 Type: LKT 250 Producer: METALPRESS Created: 1974, GO 2002 Parameters: Compressive force: 250 t Table length: 1150 mm Top table width: 1580 mm Maximum stroke rate top table: 7-25 1/min Ram stroke: 250 mm Adjusting the plunger: 100 mm Machine weight: 22950 kg GO 2002: converted to hydraulic clutch electronic control

Crank press ZAMECH PKRR 400A built in 1974. Technical data : - pressure: 400 tons - clearance between stands: 1020 mm - ram stroke: 315 mm - number of strokes per minute: 20 - maximum distance of the slider from the table closed: 742.5 mm - slider adjustment: 250 mm - table dimensions: 1020 x 1050 mm - main engine power: 40 kW - main engine revolutions: 1500 1 / min. - weight of the press: 40 t

pressure:500 tdistance between columns:3400 mmstroke:850 mmno. of strokes:9 - 18 /mindistance table/ram, max. stroke up, adjustment up:2050 mmtable surface area:3100 x 1900 mmtable height over floor:400 mmside window:1550 mmram surface:3100 x 1900 mmram adjustment:350 mmpressure of drawing cushion in ram:70 tpressure of drawing cushion in table:140 tstroke of drawing cushion in table:0 - 250 mmstroke of drawing cushion in ram:150 mmheight beneath floor:6,0 mheight over floor:8,3 mweight:155,0 tdimensions (WxDxH):5,1 x 4,5 x 12,3 mKind of drive:link drive tool changing unit:2 x

pressure:500 tdistance between columns:3400 mmstroke:850 mmno. of strokes:9 - 18 /mindistance table/ram, max. stroke up, adjustment up:2050 mmtable surface area:3100 x 1900 mmtable height over floor:400 mmside window:1550 mmram surface:3100 x 1900 mmram adjustment:350 mmpressure of drawing cushion in ram:70 tpressure of drawing cushion in table:140 tstroke of drawing cushion in table:0 - 250 mmstroke of drawing cushion in ram:150 mmheight beneath floor:6,0 mheight over floor:8,3 mweight:155,0 tdimensions (WxDxH):5,1 x 4,5 x 12,3 mKind of drive:link drive tool changing unit:2 x

pressure:500 tdistance between columns:3400 mmstroke:850 mmno. of strokes:9 - 18 /mindistance table/ram, max. stroke up, adjustment up:2050 mmtable surface area:3100 x 1900 mmtable height over floor:400 mmside window:1550 mmram surface:3100 x 1900 mmram adjustment:350 mmpressure of drawing cushion in ram:70 tpressure of drawing cushion in table:140 tstroke of drawing cushion in table:0 - 250 mmstroke of drawing cushion in ram:150 mmheight beneath floor:6,0 mheight over floor:8,3 mweight:155,0 tdimensions (WxDxH):5,1 x 4,5 x 12,3 mKind of drive:link drive tool changing unit:2 x

pressure:500 tdistance between columns:3400 mmstroke:850 mmno. of strokes:9 - 18 /mindistance table/ram, max. stroke up, adjustment up:2050 mmtable surface area:3100 x 1900 mmtable height over floor:400 mmside window:1550 mmram surface:3100 x 1900 mmram adjustment:350 mmpressure of drawing cushion in ram:70 tpressure of drawing cushion in table:140 tstroke of drawing cushion in table:0 - 250 mmstroke of drawing cushion in ram:150 mmheight beneath floor:6,0 mheight over floor:8,3 mweight:155,0 tdimensions (WxDxH):5,1 x 4,5 x 12,3 mKind of drive:link drive overload protection in ram:hydraulic ram adjustment:motoric tool changing unit:2 x

pressure:250 tthroat:450 mmstroke:36 - 126 mmno. of strokes:40 /mindistance table/ram, max. stroke up, adjustment up:525 mmtable surface area:1000 x 750 mmhole in the table:400 x 360 mmtable height over floor:1000 mmram surface:600 x 500 mmram adjustment:111 mmpower requirement:19,0 kWweight:13,5 tDimensions (WxDxH):1,3 x 3,2 x 3,35 mclutch:pneumatic overload protection in ram:mechanical ram adjustment:motoric

pressure:160 tthroat:690 mmstroke:8 - 180 mmno. of strokes:50 /mindistance table/ram, max. stroke up, adjustment up:500 mmtable surface area:1300 x 1000 mmhole in the table:400 / 120 mmtable height over floor:850 mmpassage to the back:900 mmram surface:1000 x 700 mmram adjustment:130 mmpower requirement:11,0 kWweight:19,0 tdimensions (WxDxH):2,4 x 2,8 x 3,4 mGerman Safety: permitted for manual loading:UVV 11.062 - VBG 7n5.1 clutch:pneumatic ram adjustment:motoric ram counterbalance:pneumatic

pressure: 40 tthroat: 230 mmstroke: 8-88 mmthroat: 230 mmno. of strokes: 130 Hub/minram - range of adjustment: 63 mmtable surface area: 560x450 mmram surface: 250x200 mmhole in the table: Ø 190 mmtable height: 790 mmtool hole in ram: Ø 40 mmweight of the machine ca.: 3,0 tdimensions of the machine ca.: 1000x1800x2500 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Eccentric press, single column press, punching machine, single column eccentric press, eccentric press, single column press -Manufacturer: Kaiser, punching machine with gripper feed type PO 40 F -Pressure capacity: 55 tons -Stroke: adjustable from 9 to 60 mm -Stroke rate: 70-350 strokes/min -Table size: 590 x 410 mm -Table recess: 290 x 150 mm -Projection: 220 mm -Punching fixture: Ø 38 mm -Insertion height 335 mm -Dimensions: 1905/1540/H2940 mm -Weight: 3720 kg

The press has been completely renovated. Scope of work: cleaning and repainting of the body and covers, regeneration of clutch wheel disc linings, new pneumatic installation, new electrical installation, new control (Fiessler FMSC controllers, Siemens control panel, foot limit switch), installation of feet, new user manual and documented modernization history. Original documentation available. Pressure: 25 tons Max. number of strokes/min: 125 Slider stroke: 8-60mm Slider adjustment range: 55mm Weight: 1400 kg

CONTROLS  PLC PNEUTRONIC PRESS DESIGN  drive system: knuckle-joint   frame design: H-frame, monoblock   feedstock transport direction: left to right SLIDE  total force (nominal): 250 to  stroke: 61 mm  stroke rate (max.): 60 /minCOUNTER RAM  nominal force: 75 to  stroke: 13 mmV-RING  nominal force: 75 to  stroke: 15 mmTOOL DIMENSIONS  lower table (left-right): 540 mm  lower table (front-back): 540 mm  upper table (left-right): 540 mm  upper table (front-back): 540 mm  shut height max.: 320 mm  ram adjustment: 145 mmSTRIP-FEEDER  feeder type: roll feeder   pilot release system: yes ELECTRICAL SPECIFICATIONS  mains voltage: 400 V  mains frequency: 50 HzDIMENSIONS / WEIGHTS   ...

pressure:120 tdistance between columns:430 mmstroke:125 mmdistance table/ram, stroke up:400 mmtable surface area:430 x 450 mmtable height over floor:860 mmside window:230 mmram surface:250 mmworking speed:10 mm/spower requirement:11,0 kWweight:2,5 tdimensions (WxDxH):1,6 x 1,3 x 2,4 mGerman Safety: permitted for manual loading:CE-sign

Pressure:800 tdistance between columns:2560 mmstroke:1050 mmDistance table/ram, stroke up:1870 mmTable surface area:2500 x 1730 mmpressure of drawing cushion in table:300 tDie cushion stroke in table:395 mmDie cushion area in table:2300 x 1300 mmRam surface:2500 x 1730 mmDie cushion pressure in ram:63 tDie cushion stroke in ram:150 mmSide window:1000 mmOil volume:4300 lPower capacity:200,0 kWDimensions (WxDxH):4,1 x 2,8 x 10,0 mHeight above floor:7,0 mdie cushion in table:hydraulic, controllable die cushion in ram:hydraulic, controllable

Pressure:600 tdistance between columns:2600 mmstroke:900 mmDistance table/ram, max. stroke up, adjustment up:1600 mmTable surface area:2500 x 1730 mmpressure of drawing cushion in table:250 tDie cushion stroke in table:400 mmDie cushion area in table:2300 x 1300 mmDie cushion pressure in ram:63 tDie cushion stroke in ram:160 mmDie cushion area in ram:1900 x 1300 mmRam surface:2500 x 1730 mmSide window:1100 mmOil volume:3500 lPower capacity:200,0 kWDimensions (WxDxH):4,1 x 2,8 x 9,6 mHeight above floor:6,4 mdie cushion in table:hydraulic, controllable die cushion in ram:hydraulic, controllable cutting impact absorption:hydraulic

FEINTOOL GKP F 100T fine blanking press was manufactured in Switzerland in 1974. The machine, distinguished by its robust, stable design, can perform several demanding machining steps in one precise process, saving time and labour. Workpieces with a maximum thickness of 6 mm thus achieve an extremely even surface and precisely defined edges that are impossible to achieve on other machines. The machining process can be fully automated when the FEINTOOL GKP F 100/160 hydraulic blanking press is retrofitted with a sheet metal feeder. The total weight of the machine is approximately 9 tonnes. Technical data of the FEINTOOL GKP F 100T hydraulic press - maximum workpiece thickness: 6 mm - maximum sheet metal width: 210 mm - total force including auxiliary functions: 160 t - shearing force: 100 t - hydraulic counterweight force (upper table): 1-40 t - hydraulic force of ring jaw (lower ...

Machine Type: Hydraulic Two-Column Press Manufacturer: HYDROMAK Model: P250T Year of construction: 1974 Condition: very good Offer Type: Used Machine Specifications: Compressive force: 250 t Projection: 620 mm passage Table: 610 x 610 mm Installation height: 385/515 mm Propulsion: 7.5 kW Remark: Two-handed and foot release Weight: 3200 kg The machine is in a very good condition and ready for immediate use and can be viewed and demonstrated by us. We would be pleased if you are interested in our offer. Errors, modifications and prior sale excepted.

Technical data: -maximum pressing force 40 t -maximum piston stroke 500 mm -Hoisting speed 0-40 mm / s -Return 0-200 m / min -Mounting height 750 mm -Projection up to mid slide 360 mm -Slide clamping surface 440 x 360 mm -Slide clamping pins 40 mm -Table size 630 x 500 mm -Table hole / breakthrough 200 mm -Table height above floor 710 mm -Oil quantity approx. 300 ltr -Drive 400 V / 4 kW -Space requirement approx. B H 1200 x 2800 X 1600 mm -Weight approx. 2500 kg

Working length: 3500mm, the pressure bar of the machine must be realigned. ... más información