Fabricante:
(Categoría: 106)
Connected load: 4kW, weight: 2t, an inspection is possible. ... más información
Working width: 4000mm, pressing force: 160t, control: MNC 95/C, connected load: 18kW, length: 4100mm, width: 1900mm, height: 3100mm, weight: 14.5t, including tools, the documentation is partially available, the laser system requires maintenance. ... más información
Pressure capacity: 85t/850kN, ram stroke: 30-110mm, ram adjustability: 50mm. Documentation available. ... más información
Power of parallel/offset crankshaft: 30t/2x20t, stroke: 50mm, clamping surface: 230mm/460mm, face of tappets: 2x 30mm/110mm, average of clamping journals: 38mm. Max./min. Opening front dead center: 240mm/180mm, ejection distance: 24mm. Max./min. Band width: 80(100)mm/10(5)mm, max. feed: 120mm. Running speed: 60-180rpm, drive pulley diameter: 180mm, gear reduction: 1:4, documentation available.
Compressive force: 1000kN/100t, ram stroke: 200mm, max. operating pressure: 290bar, control: DNC70, safety distance: 166mm, overtravel time: 104ms, overtravel distance: 7mm. ... más información
Compressive force: 1000kN/100t, lifting speed: 25/min, ram stroke: 230mm, power requirement: 5.5kW, safety distance: 640mm, stopping time: 400ms, weight: 4600kg. Has been overhauled once. ... más información
Pressing force: 630kN/63t, operating pressure: 270bar, stroke: 400mm, installation height: 600mm, throat depth: 280mm, oil filling: approx. 650l, weight: approx. 5200kg. Documentation available. On-site inspection is possible. ... más información
Pressing force: 2000kN, working width: 3600mm, max. stroke: 400mm, throat depth: 500mm, stops: 6, control: DNC 7000, weight: approx. 21000kg. Including various lower tools and dies with bolts as well as a holding rail. For example, prisms 7-90 and punches (straight and cranked) are included. Documentation is available. On-site inspection is possible.
There are 5 identical Otto Kaiser Pforzheim foot-operated toggle presses available. The pressing force is probably 120 kN. ... más información
Wire diameter: 16mm, number of stations: 5, length: 6700mm, width: 3800mm, height: 3050mm, including sound-proof cabin, straightener, chain hoist, sorting trough, dosing machine, oil mist separator and additional accessories. ... más información
pressure: 160 tstroke: ca. 250 mmtable surface area: 370 x 550 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG. ... más información
Pressing force: 400kN, throat depth: 520mm, dimensions X/Y/Z: 1800mm/1000mm/1900mm, weight: approx. 2600kg. Documentation available. ... más información
The data for this ad was created with ModulMWS - the software solution of LogoTech oHG. ... más información
pressure: 20 ttotal power requirement: 20 kWweight of the machine ca.: 5 tdimensions of the machine ca.: mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG. ... más información
throat: ca. 300 mmstroke: ca. 200 mmpressure capacity max.: 35 tdie cushion hydr. pressure/stroke: 15 ttotal power requirement: 5,6 kWweight of the machine ca.: ca 2,5 tdimensions of the machine ca.: 1 x 0,9 x H 2,4 m mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
CONTROLS PLC PNEUTRONIC PRESS DESIGN drive system: knuckle-joint frame design: H-frame, monoblock feedstock transport direction: left to right SLIDE total force (nominal): 250 to stroke: 61 mm stroke rate (max.): 60 /minCOUNTER RAM nominal force: 75 to stroke: 13 mmV-RING nominal force: 75 to stroke: 15 mmTOOL DIMENSIONS lower table (left-right): 540 mm lower table (front-back): 540 mm upper table (left-right): 540 mm upper table (front-back): 540 mm shut height max.: 320 mm ram adjustment: 145 mmSTRIP-FEEDER feeder type: roll feeder pilot release system: yes ELECTRICAL SPECIFICATIONS mains voltage: 400 V mains frequency: 50 HzDIMENSIONS / WEIGHTS   ...
pressure: 80 tstroke: 200 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG. ... más información
CONTROLS PLC BECKHOFF PRESS DESIGN drive system: knuckle-joint feedstock transport direction: left to right SLIDE total force (nominal): 250 to stroke: 67 mm stroke rate (max.): 80 /minCOUNTER RAM nominal force: 125 toV-RING nominal force: 125 toTOOL DIMENSIONS lower table (left-right): 560 mm lower table (front-back): 600 mm upper table (left-right): 560 mm upper table (front-back): 560 mmSTRIP-FEEDER feeder type: roll feeder DIMENSIONS / WEIGHTS total weight approx.: 14000 kgATTACHMENTS -FINEBLANKING PRESS- decoiler: optional waste cutter: yes + Control system completely renewed in 2015
CONTROLS PLC PRESS DESIGN drive system: eccentric / crank number of slide actions: 12 PRESS FORCES total force (nominal): 36 toSLIDE slide force: 3 to stroke: 38 mmSLIDE (MECHAN. PRESS) variable speed: yes main drive power: 4 kWOVERALL SPECIFICATIONS (COIL LINES) sheet width max.: 50 mm feedstock transport direction: front-back STRIP-FEEDER feeder type: roll feeder sheet width max.: 50 mm pilot release system: no band lubrication system: optional TRANSFER SYSTEM number of tool stations: 13 distance between tools, stroke X fixed: 63.5 mmELECTRICAL SPECIFICATIONS mains voltage: 400 V mains frequency: 50 HzDIMENSIONS / WEIGHTS space requirements -left/right-: 2400 mm ...
PRESS DESIGN drive system: eccentric / crank openings in uprights: yes number of suspensions: 1 number of slide actions: 1 table cushion: no PRESS FORCES total force (nominal): 125 toPRESS TABLE table surface (left-right): 1100 mm table surface (front-back): 630 mmSLIDE table surface (left-right): 700 mm table surface (front-back): 400 mm stroke: 150 mm stroke rate (max.): 70 /minSLIDE (MECHAN. PRESS) slide adjustment: 90 mm stroke adjustment: yes stroke min.: 15 mm stroke max.: 150 mm stroke rate (min.): 20 /min stroke rate (max.): 70 /min main drive power: 15 kWTOOL ASSEMBLY DIMENSIONS shut height (stroke down, adjustment up), BDC: 400 mmELECTRICAL SPECIFICATIONS ...