Fabricante:
(Categoría: 106)
Pneumatic press 2643 Assembly through pivot table outside the working area With protective cage and release only with a retracted swing table Table size: 10 cm x 10 cm ... más información
Used Hydropneumatic Press / Assembly Press / Printing Joining Press - Pressing force 10 KN (1 to) - Used hydropneumatic cylinder make TOX - Pneumatic two-hand control - Portal frame aluminum profile 90 90 mm - Machine table made of aluminum profiles and multiplex plate 700 700 mm - Total weight approx. 50 kg Suitable as an assembly press for insezing components. With x- and y-adjustment alignable vice for die diameters up to 80 mm. Or for small punching or embossing tools. All tools or vices are quickly changed through the groove system.
Hand lever press to push pins in printed circuit boards ... más información
The small laboratory press MHSP5 can perform very well with the round stamp (70 mm diameter) deformations of many materials. By delivering fine (0.5 mm per wheel revolution), deformations are carried out very accurately. Small punching or stamping operations are possible. The press is driven by a worm gear screw jacks, which requires minimal hand strength by high reduction ratio. The pressing frame consists of stable-dimensioned polyamide PA6G. Here are some technical data:-static force 5 KN (0.5 to) - portable presses frame made of polyamide PA 6 G, very stable design, with FEM program added - spindle manual jacks 20 mm, pitch 5 mm - with Handwheel diameter 120 mm and handle - gear ratio 1:10, per the Handwheel 0.5 mm screw - table size 235 195 mm - clearance width 190 mm - stamp size diameter 70 mm with 4 holes 8 mm for mounting a major stamp Very easy operation with spindle and w ...
Hand spindle press to push pins in printed circuit boards 2 presses on a plate, with a dial indicator. ... más información
Control: STE 328-89-1 1/2" complete TOX Powerhouse: S75.160.200.12D Table size: 996 x 695 mm Installation height: 600 mm Total stroke: 150 mm Power stroke: 10 mm Weight: 5700 kg Electrical connection 230 V ... más información
Capacity: 125 ton, Strokes per minute: 85-500 / min, Slide: 870 x 550 mm, Plate width: 260 mm, Year of manufacturing: 1980 ... más información
year 1985 Capacity 2500 / 2750 Ton 24900 / 27400 kN Speed 65 SPM, continuous mode Ram/Slide Stroke 12.60in, 320.00mm Ram/Slide Adjustment 0.39in, 10.00mm Shut Height (Ram / Slide Down, Adjustment Up) 35.60in, 905.00mm Stroke of Upper Knockout 2.00in, 50.00mm Stroke of Lower Knockout 2.80in, 70.00mm Ram/Slide Width 52.00 in, 1320.00 mm Ram/Slide Height 43.00 in, 1100.00 mm Bed Width 53.00 in, 1340.00 mm Bed Depth 55.00 in, 1400.00 mm power Existing Additional 28 Strokes per minute in manual mode, height shown is above floor, total height is 291 in ( 7390 mm), new quick change hydraulic type bolster Machine Length 160.00 in, 4055.00 mm Machine Width 157.00 in, 4000.00 mm machine height 264.00 in, 6710.00 mm Weight 320000 lbs, 145455 kg Condition Excellent Currently disassembled an ...
VORONEZH K8544 Hot Forging press YEAR : 1980 / 2008 OVERHAUL AND INSTALLED FORCE : 2500ton RAM STROKE : 350 mm RAM SIZE : 1120X1070 mm TABLE OVERALL SIZE : 1400X1200 mm NUMBER OF STROKES IN CONTINUOUS MODE : 60 NUMBER OF STROKES IN MANUAL MODE : 26 SHUT HEIGHT : 890 mm STROKE OF UPPER KNOCK OUT : 60 mm STOROKE OF LOWER KNOCK OUT : 70 mm MAIN MOTOR : 132KW (CHANGED TO HYUDAI HEAVY Y2012) PRESS OVERALL DIMENSION : 5380X4680X6400 mm HYDRAULIC BOLSTER NEW IN 2007 CONDITION : VERY GOOD WORKING CONDITIONS Trimming press available
SMERAL LZK 2500 Hot Forging press Fully refurbished in 2024 Capacity: 2500 Ton Speed: 65 SPM, continuous mode Ram/Slide Stroke: 320.00mm Ram/Slide Adjustment: 10.00mm Shut Height (Ram/Slide Down, Adjustment Up): 905.00mm Stroke of Upper Knockout: 50.00mm Stroke of Lower Knockout: 70.00mm Ram/Slide Width: 1320.00 mm Ram/Slide Height: 1100.00 mm Bed Width: 1340.00 mm Bed Depth: 1400.00 mm Power: 130kW Machine Length: 4055.00 mm Machine Width: 4000.00 mm Machine Height: 6710.00 mm Weight: 140000 kg Condition: like new refurbishing report: 1. Mechanical part • Complete disassembly of the press. • Measurement and troubleshooting of all parts. • The main parts of the press are tested (without destruction) in order to identify any defects. Frame: The frame was inspected and non-destructive testing of the most loaded areas was carried out. Damage to the table pl ...
2000 Ton Sumitomo Hot Forging Press line Year 2006 Stroke 350 mm (13.78") Strokes per min 75 Shut height 850 mm (33.47") SlideAdj. 7 mm (.27") Ram size 1200 mm LR X 1300 mm FB Bed size 1320 mm LR X 1300 mm FB 4 stage transfer system Slide knockout Bottom knockout Scrap System Dual Die Changer Extra Die Shoes Billet Heater and Billet Saw Also Available This line was used by HONDA to make transmission gears, It takes a billet, cuts it to size, heats it to 1300 C then the press hits it 4 times. It can determine good from bad parts, the bad parts get sent to a quench tank, the good parts get sent into a cool down conveyor that you can pick the parts up by hand at the end. The entire system was ran by one operator.
4-crank stamping press Voronezh K4537 Year: 1980 Capacity : 500 tons Ram stroke : 630 mm Stroke per minutes : 15 Max. distance between slide and table: 1400 mm Adjustment: 600mm Table size : 3180x1700 mm Cushion stroke: 300 mm Weight: 130 tons ... más información
IHI Transfer Press Model SL4-1600-450-220. With NC Feeder, Transfer System including Robots. New : 1984 Capacity : 1600 ton Stroke : 850mm Die height :1400mm Slide Adjustment : 500mm No. of Stroke : 16R.P.M Bolster Area : 4500 x 2200mm Clutch working Air Pressure : 4.5kg/cm2 ... más información
Maker: SUMITOMO HEAVY INDUSTRIES (made in Japan) Model: FPA-3000 Year: 1985 (2) Capacity & main specification 1) Capacity: 3000tf 2) Ability Limit Point: 5mm 3) Allowable eccentric load: 3000tf 4) Allowable eccentric distance: L&R 350mm 5) Slide stroke: 350mm 6) Slide stroke speed: 20~50spm 7) Stroke number: 20tpm(Max) 8) Shut height: 1200mm 9) Slide adjust distance: 10mm 10) Bed hard plate dimensions: RL 1300mm x FB 1500mm 11) Slide dimensions: RL 1200mm x FB 1400mm 12) Slide knockout capacity: Total 20tf (pin number: 4ea) 13) SKO stroke: 50mm ( adjust up) 40mm ( adjust down) 14) Bottom knockout capacity: 50tf (pin number 4ea) 15) BKO stroke: 20~30mm 16) Upright internal dimensions: RL 1400mm 17) Main motor: DC 200kw x 1450rpm 440V 18) Floor height: 6800mm 19) Working height: 1030mm 20) Side opening: FB 1000mm x TB 1400mm 21) Flywheel energy: 200tf-m (50spm) ...
(2) Asahi Sunac THP500-6 horizontal forging press (heading machine) Year: 2008 First stroke: 24 mm Second stroke: 50 mm Kickout power: 150 kN Open height: 625 mm Closed height: 425 mm Die (WxL): 500x490 mm Punch (WxL): 250x350 mm Ram stroke: 200 mm Forging force: 5000 kN Cycling time: 6.5 sec Crank speed: 60 RPM Machine weight: 28 t
Hot forging press Kurimoto C2F-16 Year: 2002 Capacity: 1600 ton Stroke: 200 mm Stroke per minute: 60 Die height: 707 mm Bolster area: 1265x890 mm Adapter area: 930x1065 mm Main motor: 75kW, 480V ... más información